Заказать запчасти 
Запчасти Case IH PTA325 (04-80) - AXLE ASSEMBLY, S-34 (04) - Drive Train
№
Артикул
Название
Примечание
Количество
1-1420
AXLE, front (23120) , consists of 1-40
1шт.
Superseded - Old P/N can be used for all models, but order new P/N when stock is depleted.
1шт.
1-5499
FRONT AXLE
AXLE, front (late 19120)
1шт.
Superseded - Old P/N can be used for all models, but order new P/N when stock is depleted.
1шт.
90-4010T91
AXLE, front (23120 w/rolled splines)
1шт.
1-1421
AXLE, rear (23120)
1шт.
Superseded - Old P/N can be used for all models, but order new P/N when stock is depleted.
1шт.
1-5502
AXLE, rear (late 19120)
1шт.
Superseded - Old P/N can be used for all models, but order new P/N when stock is depleted.
1шт.
1-1413
AXLE ASSY W/O DIFF ASSY (cut splines), consists of 1-33
2шт.
90-1821T91
AXLE ASSY W/O DIFF ASSY (rolled splines)
1шт.
1
1-1357
ROLLER BEARING,133.35mm ID x 39.69mm W
CONE, bearing
4шт.
The 2-1097 hub, ref. 21, may no longer be available. If so it can be serviced with kit no. 35-1567T91 which incl. a 90-1825T2 hub and new outer hub bearings to replace ref. 1 and 2. These are a 16-755 cone and 16-206 cup. For identification purposes the 16-1206 cup has a 7-3/4 " O.D. while the standard 1-1358 has a 7-1/2' O.D. This repair would not have occured until after Jan 84.
1шт.
2
1-1358
BEARING CUP,190.5mm OD x 33.34mm W
CUP, bearing
4шт.
The 2-1097 hub, ref. 21, may no longer be available. If so it can be serviced with kit no. 35-1567T91 which incl. a 90-1825T2 hub and new outer hub bearings to replace ref. 1 and 2. These are a 16-755 cone and 16-206 cup. For identification purposes the 16-1206 cup has a 7-3/4 " O.D. while the standard 1-1358 has a 7-1/2' O.D. This repair would not have occured until after Jan 84.
1шт.
3
1-1394
THRUST WASHER
thrust
2шт.
4
1-1355
BUTTON
thrust
2шт.
5
1-1356
STRIP
TAB, locking
6шт.
6
1-1360
CLIP,ELECTRICAL
CLIP, retaining
6шт.
7
1-1361
WASHER
2шт.
8
1-1393
BALL
6шт.
9
90-3839T1
SEAL
(01-1351)
2шт.
Superseded - Old P/N can be used for all models, but order new P/N when stock is depleted.
1шт.
35-1346T91
SEAL
WEAR SLEEVE KIT, repair grooved spindle, 35-1346T91 is not needed if 90-3839T1 seal is used, for more info see Steiger service news bulletin SN0120
2шт.
11
1-1349
NUT
2шт.
12
1-1363
LOCK WASHER
WASHER (.075 thick)
2шт.
A later spindle, 90-3841T2, can be used to replace 2-1096, but if done, a new washer , 90-4378T1, ref. 12, which is .10 thick and is made to fit the deeper groove on 90-3841T2, must be ordered
1шт.
90-4378T1
LOCK WASHER
(.10 thick) (used only with 90-3841T2)
2шт.
A later spindle, 90-3841T2, can be used to replace 2-1096, but if done, a new washer , 90-4378T1, ref. 12, which is .10 thick and is made to fit the deeper groove on 90-3841T2, must be ordered
1шт.
13
1-1359
BREATHER
VENT
1шт.
14
1-1354
ROLLER BEARING,0.375" OD x 1.46"
BEARING, roller
288шт.
15
1-1403
SHAFT
axle (22 cut splines)
2шт.
90-1820T1
AXLE SHAFT
SHAFT, axle (36 rolled splines)
1шт.
16
1-1400
RING
GEAR, ring
1шт.
17
1-1404
STEERING KNUCKLE
SPINDLE (early) (5/8" Mt holes)
2шт.
Superseded, old P/N must be used on models prior to S/N break new P/N will fit models after the S/N break only
1шт.
2-1521
STEERING KNUCKLE
SPINDLE (2nd style) (3/4" countersunk Mt holes)
1шт.
Superseded, old P/N must be used on models prior to S/N break new P/N will fit models after the S/N break only
1шт.
2-1096
STEERING KNUCKLE
SPINDLE (3/4" Mt holes)
1шт.
Superseded, old P/N must be used on models prior to S/N break new P/N will fit models after the S/N break only
1шт.
A later spindle, 90-3841T2, can be used to replace 2-1096, but if done, a new washer , 90-4378T1, ref. 12, which is .10 thick and is made to fit the deeper groove on 90-3841T2, must be ordered
1шт.
90-3841T2
STEERING KNUCKLE
SPINDLE (service only, not used on production axles)
1шт.
A later spindle, 90-3841T2, can be used to replace 2-1096, but if done, a new washer , 90-4378T1, ref. 12, which is .10 thick and is made to fit the deeper groove on 90-3841T2, must be ordered
1шт.
18
1-1405
HOUSING (early) (5/8" spindle Mt holes)
1шт.
Superseded, old P/N must be used on models prior to S/N break new P/N will fit models after the S/N break only
1шт.
2-1098
HOUSING (later ) (3/4" spindle Mt holes)
1шт.
Superseded, old P/N must be used on models prior to S/N break new P/N will fit models after the S/N break only
1шт.
19
1-1406
CARRIER
planet
2шт.
20
1-1402
RING
HUB, ring gear
2шт.
21
1-1401
HUB
wheel (early)
2шт.
Superseded, old P/N can be used up on all models prior to S/N break only, new P/N must be used after S/N break, order new P/N when old stock is depleted as it will work for all
1шт.
2-1097
HUB
wheel (late)
1шт.
Superseded, old P/N can be used up on all models prior to S/N break only, new P/N must be used after S/N break, order new P/N when old stock is depleted as it will work for all
1шт.
The 2-1097 hub, ref. 21, may no longer be available. If so it can be serviced with kit no. 35-1567T91 which incl. a 90-1825T2 hub and new outer hub bearings to replace ref. 1 and 2. These are a 16-755 cone and 16-206 cup. For identification purposes the 16-1206 cup has a 7-3/4 " O.D. while the standard 1-1358 has a 7-1/2' O.D. This repair would not have occured until after Jan 84.
1шт.
22
1-1399
PINION
GEAR, planet
6шт.
23
1-1353
PIN
Planet gear
6шт.
24
1-1398
OIL SEAL
SNAP RING
6шт.
25
1-1350
PLUG
expansion
6шт.
26
1-3093
LARGE PLATE
PLATE, thrust
12шт.
27
1-1396
SPACER
6шт.
28
1-1395
O-RING,3.484" ID x 3.762" OD x 0.139"
(qty 2 w/90-3841T2, ref 17)
4шт.
29
454862
BOLT,Hex, 5/16" - 18 x 3/4", Gr 8
CAPSCREW
12шт.
30
271562
SHIELD,Hex, 5/8" - 11 x 2", Gr 5
CAPSCREW
64шт.
31
19-840
BOLT,1/2" - 13 x 2 1/2", Gr 5
CAPSCREW (use w/01-1405 housing)
24шт.
19-1920
SCREW,Flg, 3/4" - 10 x 2 1/4", Gr 8
CAPSCREW SOCKET HEAD (use w/02-1098 housing)
1шт.
32
31-531
PLUG
4шт.
33
1-1352
RING
pilot (not used w/90-3841T2)
2шт.
34
90-1844T91
DIFF ASSY, front (23120, ID #999999)
1шт.
1-5497
DIFF ASSY, front (lat 19120, ID # 106455)
1шт.
90-1877T91
DIFF ASSY, front (23120, ID #115049) (w/rolled spline side gears)
1шт.
90-1843T91
NO LONGER SERVICED
DIFF ASSY, rear (23120, ID #98545)
1шт.
1-5495
DIFF ASSY, rear (late 19120, ID #106453)
1шт.
90-1878T91
DIFFERENTIAL ASSY
DIFF ASY, rear (23120, ID #107942) (w/rolled spline side gears)
1шт.
35
19-817
SCREW,Hex, 5/8"-11 x 2", G8
CAPSCREW
8шт.
19-840
BOLT,1/2" - 13 x 2 1/2", Gr 5
CAPSCREW
4шт.
36
19-2974
BOLT,Hex, 7/8" - 9 x 2 1/4", Gr 8
LUG BOLT
20шт.
223470
BOLT,Hex, 7/8" - 9 x 2 1/2", Gr 8
LUG BOLT (use when wheel has 3/4" thick disc)
1шт.
19-2975
WASHER
(used w/lug bolt )
20шт.
37
1-5513
FORK
YOKE
1шт.
38
19-815
BOLT,Hex, 1" - 8 x 9 1/4", Gr 8
AXLE BOLT (PT front/rear & PTA rear axles only)
8шт.
19-1318
BOLT,Hex, 1" - 8 x 10 1/2", Gr 8
AXLE BOLT (PTA front axle only)
1шт.
19-1121
BOLT,Hex, 1" - 8 x 10", Gr 8
AXLE BOLT (used w/axle stops on rear frame only)
1шт.
39
19-859
LOCK NUT
axle bolt
8шт.
40
16-46
SCREW
GASKET, carrier
1шт.
35-1175
NO LONGER SERVICED
SPINDLE KIT, includes ref 17, 02-1521 spindle and 12, ref 31 bolts, will upgrade the early axles to the heavier spindle mt bolts if problem exists with bolt breakage.
1шт.
Выбрано товаров: 88