Запчасти Case IH PT270 (04-80) - AXLE ASSEMBLY, S-34 (04) - Drive Train

1-1420

AXLE, front (23120) , consists of 1-40

1шт.

Superseded - Old P/N can be used for all models, but order new P/N when stock is depleted.

1шт.

1-5499

FRONT AXLE

AXLE, front (late 19120)

1шт.

Superseded - Old P/N can be used for all models, but order new P/N when stock is depleted.

1шт.

90-4010T91

AXLE, front (23120 w/rolled splines)

1шт.

1-1421

AXLE, rear (23120)

1шт.

Superseded - Old P/N can be used for all models, but order new P/N when stock is depleted.

1шт.

1-5502

AXLE, rear (late 19120)

1шт.

Superseded - Old P/N can be used for all models, but order new P/N when stock is depleted.

1шт.

90-4011T91

CENTER AXLE

AXLE, rear (23120 w/rolled splines)

1шт.

1-1413

AXLE ASSY W/O DIFF ASSY (cut splines), consists of 1-33

2шт.

90-1821T91

AXLE ASSY W/O DIFF ASSY (rolled splines)

1шт.

1

1-1357

ROLLER BEARING,133.35mm ID x 39.69mm W

CONE, bearing

4шт.

The 2-1097 hub, ref. 21, may no longer be available. If so it can be serviced with kit no. 35-1567T91 which incl. a 90-1825T2 hub and new outer hub bearings to replace ref. 1 and 2. These are a 16-755 cone and 16-206 cup. For identification purposes the 16-1206 cup has a 7-3/4 " O.D. while the standard 1-1358 has a 7-1/2' O.D. This repair would not have occured until after Jan 84.

1шт.

2

1-1358

BEARING CUP,190.5mm OD x 33.34mm W

CUP, bearing

4шт.

The 2-1097 hub, ref. 21, may no longer be available. If so it can be serviced with kit no. 35-1567T91 which incl. a 90-1825T2 hub and new outer hub bearings to replace ref. 1 and 2. These are a 16-755 cone and 16-206 cup. For identification purposes the 16-1206 cup has a 7-3/4 " O.D. while the standard 1-1358 has a 7-1/2' O.D. This repair would not have occured until after Jan 84.

1шт.

3

1-1394

THRUST WASHER

thrust

2шт.

4

1-1355

BUTTON

thrust

2шт.

5

1-1356

STRIP

TAB, locking

6шт.

6

1-1360

CLIP,ELECTRICAL

CLIP, retaining

6шт.

7

1-1361

WASHER

2шт.

8

1-1393

BALL

6шт.

9

90-3839T1

SEAL

(01-1351)

2шт.

Superseded - Old P/N can be used for all models, but order new P/N when stock is depleted.

1шт.

35-1346T91

SEAL

WEAR SLEEVE KIT, repair grooved spindle, 35-1346T91 is not needed if 90-3839T1 seal is used, for more info see Steiger service news bulletin SN0120

2шт.

10

1-1397

O-RING,14.984" ID x 15.262" OD x 0.139"

2шт.

11

1-1349

NUT

2шт.

12

1-1363

LOCK WASHER

WASHER (.075 thick)

2шт.

A later spindle, 90-3841T2, can be used to replace 2-1096, but if done, a new washer , 90-4378T1, ref. 12, which is .10 thick and is made to fit the deeper groove on 90-3841T2, must be ordered

1шт.

90-4378T1

LOCK WASHER

(.10 thick) (used only with 90-3841T2)

2шт.

A later spindle, 90-3841T2, can be used to replace 2-1096, but if done, a new washer , 90-4378T1, ref. 12, which is .10 thick and is made to fit the deeper groove on 90-3841T2, must be ordered

1шт.

13

1-1359

BREATHER

VENT

1шт.

14

1-1354

ROLLER BEARING,0.375" OD x 1.46"

BEARING, roller

288шт.

15

1-1403

SHAFT

axle (22 cut splines)

2шт.

90-1820T1

AXLE SHAFT

SHAFT, axle (36 rolled splines)

1шт.

16

1-1400

RING

GEAR, ring

1шт.

17

1-1404

STEERING KNUCKLE

SPINDLE (early) (5/8" Mt holes)

2шт.

Superseded, old P/N must be used on models prior to S/N break new P/N will fit models after the S/N break only

1шт.

2-1521

STEERING KNUCKLE

SPINDLE (2nd style) (3/4" countersunk Mt holes)

1шт.

Superseded, old P/N must be used on models prior to S/N break new P/N will fit models after the S/N break only

1шт.

2-1096

STEERING KNUCKLE

SPINDLE (3/4" Mt holes)

1шт.

Superseded, old P/N must be used on models prior to S/N break new P/N will fit models after the S/N break only

1шт.

A later spindle, 90-3841T2, can be used to replace 2-1096, but if done, a new washer , 90-4378T1, ref. 12, which is .10 thick and is made to fit the deeper groove on 90-3841T2, must be ordered

1шт.

90-3841T2

STEERING KNUCKLE

SPINDLE (service only, not used on production axles)

1шт.

A later spindle, 90-3841T2, can be used to replace 2-1096, but if done, a new washer , 90-4378T1, ref. 12, which is .10 thick and is made to fit the deeper groove on 90-3841T2, must be ordered

1шт.

18

1-1405

HOUSING (early) (5/8" spindle Mt holes)

1шт.

Superseded, old P/N must be used on models prior to S/N break new P/N will fit models after the S/N break only

1шт.

2-1098

HOUSING (later ) (3/4" spindle Mt holes)

1шт.

Superseded, old P/N must be used on models prior to S/N break new P/N will fit models after the S/N break only

1шт.

19

1-1406

CARRIER

planet

2шт.

20

1-1402

RING

HUB, ring gear

2шт.

21

1-1401

HUB

wheel (early)

2шт.

Superseded, old P/N can be used up on all models prior to S/N break only, new P/N must be used after S/N break, order new P/N when old stock is depleted as it will work for all

1шт.

2-1097

HUB

wheel (late)

1шт.

Superseded, old P/N can be used up on all models prior to S/N break only, new P/N must be used after S/N break, order new P/N when old stock is depleted as it will work for all

1шт.

The 2-1097 hub, ref. 21, may no longer be available. If so it can be serviced with kit no. 35-1567T91 which incl. a 90-1825T2 hub and new outer hub bearings to replace ref. 1 and 2. These are a 16-755 cone and 16-206 cup. For identification purposes the 16-1206 cup has a 7-3/4 " O.D. while the standard 1-1358 has a 7-1/2' O.D. This repair would not have occured until after Jan 84.

1шт.

22

1-1399

PINION

GEAR, planet

6шт.

23

1-1353

PIN

Planet gear

6шт.

24

1-1398

OIL SEAL

SNAP RING

6шт.

25

1-1350

PLUG

expansion

6шт.

26

1-3093

LARGE PLATE

PLATE, thrust

12шт.

27

1-1396

SPACER

6шт.

28

1-1395

O-RING,3.484" ID x 3.762" OD x 0.139"

(qty 2 w/90-3841T2, ref 17)

4шт.

29

454862

BOLT,Hex, 5/16" - 18 x 3/4", Gr 8

CAPSCREW

12шт.

30

271562

SHIELD,Hex, 5/8" - 11 x 2", Gr 5

CAPSCREW

64шт.

31

19-840

BOLT,1/2" - 13 x 2 1/2", Gr 5

CAPSCREW (use w/01-1405 housing)

24шт.

19-1920

SCREW,Flg, 3/4" - 10 x 2 1/4", Gr 8

CAPSCREW SOCKET HEAD (use w/02-1098 housing)

1шт.

32

31-531

PLUG

4шт.

33

1-1352

RING

pilot (not used w/90-3841T2)

2шт.

34

90-1844T91

DIFF ASSY, front (23120, ID #999999)

1шт.

1-5497

DIFF ASSY, front (lat 19120, ID # 106455)

1шт.

90-1877T91

DIFF ASSY, front (23120, ID #115049) (w/rolled spline side gears)

1шт.

90-1843T91

NO LONGER SERVICED

DIFF ASSY, rear (23120, ID #98545)

1шт.

1-5495

DIFF ASSY, rear (late 19120, ID #106453)

1шт.

90-1878T91

DIFFERENTIAL ASSY

DIFF ASY, rear (23120, ID #107942) (w/rolled spline side gears)

1шт.

35

19-817

SCREW,Hex, 5/8"-11 x 2", G8

CAPSCREW

8шт.

19-840

BOLT,1/2" - 13 x 2 1/2", Gr 5

CAPSCREW

4шт.

36

19-2974

BOLT,Hex, 7/8" - 9 x 2 1/4", Gr 8

LUG BOLT

20шт.

223470

BOLT,Hex, 7/8" - 9 x 2 1/2", Gr 8

LUG BOLT (use when wheel has 3/4" thick disc)

1шт.

19-2975

WASHER

(used w/lug bolt )

20шт.

37

1-5513

FORK

YOKE

1шт.

38

19-815

BOLT,Hex, 1" - 8 x 9 1/4", Gr 8

AXLE BOLT (PT front/rear & PTA rear axles only)

8шт.

19-1318

BOLT,Hex, 1" - 8 x 10 1/2", Gr 8

AXLE BOLT (PTA front axle only)

1шт.

19-1121

BOLT,Hex, 1" - 8 x 10", Gr 8

AXLE BOLT (used w/axle stops on rear frame only)

1шт.

39

19-859

LOCK NUT

axle bolt

8шт.

40

16-46

SCREW

GASKET, carrier

1шт.

1-3467

PAD

AXLE PAD (PTA front axle only) (not shown)

2шт.

35-1175

NO LONGER SERVICED

SPINDLE KIT, includes ref 17, 02-1521 spindle and 12, ref 31 bolts, will upgrade the early axles to the heavier spindle mt bolts if problem exists with bolt breakage.

1шт.